Reboot MIG Welder 135A 230V IGBT 1KG gasless MIG

Product Description

How to install the belt:

1. Take the parts of the belt and prepare to install the belt on the welder.

2. Thread the belt on both sides of the machine.

3. Adjust the belt length to your needs.

4. The weight of the welding machine only 5.4 kg, small.

5. It is very suitable for carrying on the shoulder to continue the welding process. The belt is soft and adjusts to the angle according to the shoulder and the shoulder will not hurt even after a long time.

About MIG135E

• Self-protected welding with flux cored wire, easy welding.
• MIG without gas
• Standardization of the integration of EMC card and motherboard
• IGBT inverter technology
• The wire feed speed and voltage are automatically adjusted and the current / voltage is automatically set to the best value.
• Durable, fan quiet, overheating / overcurrent / overvoltage protection
• The welding gun is an integrated MIG15 torch with a length of 2 meters

Error symptom Remedy

• The power indicator does not light up, the fan does not work and the welding current is missing:
• 1. Make sure the air switch is closed.
• 2. Check that the wire mesh is working.
• 3. Some of the (four) heat variable resistors on the power panel are damaged. In this case the general DC14V relay is open or the connections are poorly connected.
• 4. Power panel (bottom) is damaged, DC 130V voltage cannot be output.
• (1) The silicone bridge is broken or the silicone bridge connector has poor contact.
• (2) The power panel has burned out.
• (3) Check whether the contact and the plug-in cable from the air switch to the power panel have poor contact, check whether the contact and the plug-in cable from the power panel to the IGBT board are reliably connected.
• 5. The auxiliary power supply to the control center is defective.
• Power indicator is on, fan is running, no solder emissions
• 1. Check if all types of cables between machines are making poor contact.
• 2. The output connector is defective
• 3. The output connector is defective or not properly connected. 4. The control circuit is interrupted.
• The operating indicator lights up, the fan is running, the fault indicator lights up.
• 1. It may be overheating protection, turn off the power first, then turn it on again after the abnormal indicator goes out.
• 2. Maybe it's overheating protection, please wait 2-3 minutes.
• 3. Possibly the circuit of the inverter is interrupted, unplug the mains plug of the main transformer, which is located on the IGBT board, and open the machine again:
• 1) If the fault indicator is still on, some of the field transistors on the IGBT board are damaged, locate them and replace with the same model.
• 2) If the abnormal indicator does not light up:
• A: The central PCB transformer may be damaged, measure the volume of the inductor and the volume Q of the main transformer across the inductor bridge. If the volume is too low, replace it.
• B. The transformer secondary rectifier tube may be damaged, correct the problem and replace the rectifier tube.

Input voltage	230V	230V	230V	16 In	150A	0.8mm
Current area	40-130A	40-150A	40-160A
Material	Stainless steel/carbon steel/mild steel/other metal material	Stainless steel/carbon steel/mild steel/other metal material	Stainless steel/carbon steel/mild steel/other metal material
welding thickness/Max cutting thickness	≥0.8mm	≥0.8mm	≥0.8mm
Degree of utilization	60%	60%	60%
Function	MIG GAS/MIG GASLESS/MMA/Lift TIG	MIG GAS/MIG GASLESS/MMA/Lift TIG/Spool Gun	MIG GAS/MIG GASLESS/MMA/Lift TIG
Cable diameter	0.8mm/1.0mm	0.8mm/1.0mm	0.8mm/1.0mm
Welding materials	Carbon steel/Stainless steel/alloy steel/mild steel/copper/cast iron/chrome	Carbon steel/Stainless steel/alloy steel/mild steel/copper/cast iron/chrome	Carbon steel/Stainless steel/alloy steel/mild steel/copper/cast iron/chrome
Welding wire specifications	1KG	1KG	1KG/5KG
Package weight	8.8KG	11KG	12.8KG